CAN Supply Cable for Swing & Bow Pro Thruster
VETUS CAN-bus Power Supply Cable for Bow Pro & Swing thruster systems.
Manufacturer Part No. : BPCABCPC
UPC Code:
VETUS CAN Supply Cable f/Swing & Bow Pro Thruster
$138.00
CAN Supply Cable for Swing & Bow Pro Thruster
VETUS CAN-bus Power Supply Cable for Bow Pro & Swing thruster systems.
Description
Related products
Boat Leveler 12″ x 9″ Trim Tab Set
Features:
Wiring
- Color-coded wiring in 25' to 40' lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn't exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim's hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15' of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Boat Leveler Tab Locator – Black
Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
position of your tabs. Two seperate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.
Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.
Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.
Boat Leveler Hydraulic Cylinder
Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
Cylinder is 7 1/2 inches eye to eye when closed.
Cylinder is 7 1/2 inches eye to eye when closed.
Furuno Table Top Display Mounting Bracket f/ MU-155C Display
Display Table Top Mounting Bracket with Knobs and Screws
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
NavPod AG126 Pedestal Guard
AG126 Pedestal Guard
Double Bend AngleGuard 9.5″ Wide 1.25″ for one InstrumentPod and a large GP1030 or GP1060 SailPod below on the angled section. AngleGuards are available in 1” or 1.25” diameter stainless steel tubes.
Features:
- 316 grade stainless steel
- .065 gauge wall thickness
- Mirror polished finish
- All 1.25” include stainless steel feet (1” does not include feet)
Boat Leveler 12″ x 8″ Trim Tab Set
Features:
Wiring
- Color-coded wiring in 25' to 40' lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn't exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim's hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15' of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
