Yamaha 75-250 HP Small Aluminum Anode for Crankcase Cylinder
Engine Cylinder Head Aluminum Anode Yamaha.
Manufacturer Part No. : 01156-1AL
UPC Code:
Tecnoseal Yamaha 75-250 HP Small Aluminum Anode f/Crankcase Cylinder
$5.53
Yamaha 75-250 HP Small Aluminum Anode for Crankcase Cylinder
Engine Cylinder Head Aluminum Anode Yamaha.
Description
Related products
Boat Leveler Hydraulic Hose – Sold By The Foot
Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 400lb working pressure. Entering the transom 6" above the water line, the hoses are held securely with hose trim. Stainless steel clamps hold the hose to barb fitting at the solenoid.
Boat Leveler 14″ x 11″ Trim Tab Set
Features:
Wiring
- Color-coded wiring in 25' to 40' lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn't exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim's hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15' of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
NavPod PP5050 PowerPod Uncut Grand Prix Series
| PART #: | |
| Description: | PowerPod, Uncut |
| (usable face = 12.75"w x 8.55"h) | |
| W x H x D: | 15.125" x 13" x 10" |
NavPod Protects Your Electronics In Harsh Conditions
PowerPod Grand Prix Series with 20/40 Swivel Base
PowerPods are simply a better way to mount your Radar/Chartplotter, Fishfinder or GPS. You combine the clean look of flush mounting with the features of a swivel base. Turn the PowerPod to get the best view of your color display. Let your co-pilot enter the waypoints while you steer the boat, then swivel the display back for you to see.
The Latest In Industrial Design
Built to complement the latest marine electronic products.
Double Seal for Watertight Integrity
Outer silicone seal is complemented by an internal seal made of memory resistant urethane foam gasketing that keeps its shape and sealing ability over many years.
Polished Stainless Steel TamperProof Fasteners
Large size and strength with new buttonhead style screws that have deep wrench recesses for better tightening power. UV stable polyurethane washers under each fastener improves sealing and holding power of fasteners and long 6 tamperproof wrench provided for easier assembly.
Pre-Cut Models
Includes all of the necessary parts in order to flush mount the unit Comes with a Flush Mount kit which includes a specific gasket and mounting hardware if not supplied by the manufacturer with the unit.
NavPod GP1040 SailPod Uncut f/9.5″ Pedestal Guards
| PART #: | |
| Description: | Uncut (usable face = 17.5"w x 7.375"h) |
| W x H x D: | 20.25" x 9.5" x 6.125" |
NavPod Protects Your Electronics In Harsh Conditions
Un-Cut NavPods are for you to choose your own layout or for mounting electronics that NavPod doesn't provide a Pre-Cut for. The face of the NavPod can easily be cut with a "Rotozip". It's a small handheld router style cutter that shreds the material while cutting. This eliminates any melting of the plastic material. It is also important to note that when selecting a possible Un-cut NavPod, the depth measurement stated in the chart is overall outside measurement. Actual internal clearance can be reduced by curvature from the design or molded indents for the mounting system. This can reduce the overall and needs to be considered when making a determination of actual available depth clearance.
Watertight Silicone Seal
Keeps rain and salt water spray off electrical connections on the back of electronics
Tamperproof
Special fasteners and wrench are included that provide security and convenience to leave electronics on-board
Concealed Wiring
No loose wires are exposed to corrosion and UV damage
Clean Installation
The clean look of flush mounting. Mount your display where you can best see and reach it.
Pre-Cut Models
Come with a Flush Mount Kit, which includes the specific gasket and mounting hardware for your electronics if not supplied by manufacturer with unit.
Boat Leveler 12″ x 11″ Trim Tab Set
Features:
Wiring
- Color-coded wiring in 25' to 40' lengths with quick connects fittings, meets federal standards for heat, pull and insulation, making installation easy.
Solenoids
- They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
Motor
- A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled.
Brackets
- Swivel type brackets allow cylinders to be mounted an adjusted to any angle. Knockout pins act as shear pins it tab strikes an object.
Pump
- Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn't exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Motor Cover
- 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down.
Cylinders
- Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus O-ring, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevents hose blow-off and breakage.
A stainless steel spring retracts the cylinder when the boat is not in motion.
Trim Tabs
- 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim's hinges prevent most spray and can be used for transom or bottom mounting.
Hose
- Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15' of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim.
Stainless steel clamps hold the hose to barb fitting at the solenoid.
Rocker Type Controls
- Mounted on the dash they are easy to operate.
One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
NavPod AG126 Pedestal Guard
AG126 Pedestal Guard
Double Bend AngleGuard 9.5″ Wide 1.25″ for one InstrumentPod and a large GP1030 or GP1060 SailPod below on the angled section. AngleGuards are available in 1” or 1.25” diameter stainless steel tubes.
Features:
- 316 grade stainless steel
- .065 gauge wall thickness
- Mirror polished finish
- All 1.25” include stainless steel feet (1” does not include feet)
Boat Leveler Solenoid Valve – Green Wires
Insta-Trim Boat Leveler 12 Volt Solenoid Valve with Green Wire. They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating driftback. Barb type hose fittings provide tight, secure connections.
